TZ-V-3L

30/40/80m Low Band Trapped Vertical Antenna

SPECIFICATIONS

The TZ-V-3L trapped vertical features include:

  • Operating bands 30/40/80m
  • Max Operating power 1 kW PEP, 500W CW continuous
  • Typical impedance 35 ohm - 50 ohm (depending on installation)
  • Gain -1.0 to 0 dBd
  • Effective Gain 1.4 dBi typical (when 32 or more radials)
  • VSWR 1.5:1 (typical)
  • Bandwidth 30m, 40m (200kHz) and 80m (120kHz)
  • Total length 11.20m approx
  • Wind Survival 80 kmph
  • Shipping length 1.95m
  • Weight 7.5 kgs (approx 16 lb)

PRICE:   $599.00

Available via special order only. Order time 4 to 6 weeks.

ANTENNA DESCRIPTION

The TZ-V-3L is a tri-band trapped vertical antenna designed to permit operation on the lower DX amateur bands of 30/40/80m. If you've got a tight budget or a small yard or terrace house, why not give the HF DX frequencies a shot with a vertical. When mounted in the clear at a height of 4m or more the antenna will provide outstanding DX signals due to the low angle of radiation. Radiation patterns of the antenna will soon be available on this web site.

MOUNTING CONSIDERATIONS

The TZ-V-3L can be mounted in one of two (2) ways:

  1. Mount the antenna on the ground using a 50mm diameter galvanised steel pipe, 1000mm long or greater. Use a sledge hammer to insert the pipe into the ground or dig a hole and bury it so that approximately 300m protrudes above ground. Directly mount the vertical to the pipe. It is advisable to install a 2.0m or greater length of copper clad steel earthing bar next to the antenna to provide an adequate earth. Connect as many earth radials as possible for optimum low angle radiation and efficiency of your antenna.
  2. Mount the antenna on a metal deck roof (your garage for instance) and use the metallic structure as the ground plane for the antenna. Again a 50mm diameter pipe is recommended and the metal structure should have at least 1m2 of metal surface area.
  3. Pole mounting in not recommended due to the size of this antenna.

ANTENNA CONSTRUCTION

Acetal plastic insulating sections are used for mechanical strength and stiffness so that the antenna can handle strong winds. The lower section of the antenna is 32mm O.D, tapering down to 12mm O.D. at the top. Trap covers are provided for bird and rodent protection rather than weather protection since the traps are fully sealed. The coaxial traps provide excellent isolation from band to band and their high Q ensures low losses. The bandwidth of the antenna is remarkable for a trapped antenna and the complete bandwidth of each bands is covered with VSWR under 2.0:1 when correctly tuned.

Stainless steel fasteners are used (except for mounting U bolts which are optionally S/S) as well as aluminium rivets for reduced corrosion. Three (3) stainless steel hose clamps are used to permit adjustment of the antenna on each band. Assembly is simple and straightforward, and if by chance something does go wrong most parts can be obtained from your local hardware store, e.g. nuts, screws, rivets, U bolts etc.

The Rippletech radial kit is recommended for tower or mast mounting of the antenna. Optional S/S mounting U bolts are also available instead of the zinc plated version for an additional cost of $25.00 inclusive of GST.

The TZ-V-3L is supplied with all stainless steel hardware except for the boom/pole mount U bolts (optionally S/S).

[Home] [Products] [Trapped Vertical Antennas] [Rotary Dipole Antennas] [Baluns] [Accessories] [Wire Antennas] [Price List] [Contact Us] [How to Order] [Downloads] [News & Info] [New Products] [Testimonials] [Other Links]